Month: September 2019

When it comes to selecting a type of sewer lining for a new installation or to repair an old pipe system,it can be overwhelming for property owners to discover that there are several different products on the market. As repairing the lining of pipes can be tricky job,each of these methods and types of equipment are best for different types of sewer systems.

Some of the most common types of sewer lining equipment are Cured-in-Place Piping (CIPP),Pull-in-Place Lining (PIP),Pipe Bursting and Internal Pipe Coating. Each of these methods can be used on various types of pipes,either to repair them or to replace them completely.

The first solution is Internal Pipe Coating,which is a process used to repair old,leaky plumbing pipes by leaving the pipe structure in place. Instead of pipes being replaced,the interior of the system is coated with an epoxy coating,which is sprayed into the pipes after the water has been drained from the system and the interior prepared for the treatment.

This is a common choice of solution in residential and commercial properties,as it is non-disruptive and does not involve the destruction of any floors or walls to gain access to the pipes and apply the product. When done properly,this type of treatment can leave pipes and drain age systems even better than new,with increased water flow.

Another type of sewer lining equipment is CIPP,which – similarly to the epoxy coating method mentioned above – works to improve the interior of pipes without replacing them entirely. This is often used to reinforce sections of pipe that have become damaged,but are not in such bad condition that they must be replaced.

This method works by placing the lining into the section of pipe where it is needed,after the pipe has been prepared by thoroughly cleaning and drying the interior. The liner is fixed in place using jets of hot steam,and as a result the lining will fit seamlessly into all the nooks,crannies and cracks that are present on the inside of the pipe.

Similarly to the first method,this type of sewer lining equipment does not require removing part of the floors,walls or ceiling of a property,and therefore is useful in all kinds of buildings without compromising the structure of the building. This also means that normal occupant activity in the building is not disrupted.

Next is PIP,which is pulled into place – as the name suggests – and is then fixed to the interior of the pipe using a hot steam method as with CIPP,or by using an alternative technique using heat. The lining in this instance is made from slightly different material from the CIPP lining,typically resin and fiber glass.

This liner is useful for pipes which are slightly more damaged than in the instances mentioned above,and especially where there are some gaps or cracks present in the pipes.

For those severely damaged pipes,the final method of Pipe Bursting is most appropriate for this,as it is aimed at entirely replacing an entire pipe system or a large section of a sewer installation. In this case,it is necessary to gain physical access to the existing pipes,so some disruption will be caused as holes need to be made.

This method works by placing a large ‘bursting head’ at the entrance to a pipe,and then drawing it mechanically through the pipe. As it travels through pipe,it breaks apart the old pipe and draws a new pipe behind it,which replaces the old system as the bursting head goes along.

From a simple but effective coating to a complete pipe replacement with Pipe Bursting,there are many different types of sewer liners and equipment used to replace damaged sewer systems. The method used ultimately depends on the level of damage to the existing pipes and what type of building the system is in.

Your water heater is one of the most used and more expensive appliances in your home,and consumes a large portion of your energy dollars each month. And experts say regular care and maintenance is essential to protecting your investment and saving on your home heating and energy costs.

Regular flushing of your water heater is probably the single most important step you can take to prolong its service life and to save energy. Over a period of time,sediments build up in the bottom of your water heater. These sediments act as a barrier between the flame and the tank,thereby making your heater burn longer and hotter. This is not only destructive to the tank,but highly inefficient and will significantly raise your heating costs.

In most areas of the country,the average water heater lasts 3-5 years. Regularly flushing your water heater can double the life of your water heater from 3-5 to 7-10 years. And with the costs of replacement running from $700 to over $1200 in some cases,getting the most out of your heater is critical in today’s economy. In addition,regular flushing makes your water heater run more efficiently and can cut heating costs in half. Depending on the volume of hot water your home uses,that can mean a savings of $20 to over $50 a month.

To drain your water heater,first you should set the thermostat to pilot (if it is a gas water heater) or turn the circuit breaker off (if it is an electric heater). Failure to do so could result in overheating and severe damage to the water heater. Next,close the water supply valve located on the water inlet line going into your water heater. You can then connect a garden hose to the drain valve located at the bottom of the heater. Open the drain and allow it to run until all of the water has emptied from the heater. Then close the drain. Open the water supply valve and refill the heater. You should also open a hot water faucet somewhere inside the house and stand there and watch it run for several minutes until the water flows out smoothly. This will allow air to vent from the heater and the hot water lines. Finally,you can turn the thermostat back to its regular setting (for a gas heater),or turn the circuit breakers back on (for an electric heater).

Besides regularly flushing your water heater,plumbing experts also advise adding a water treatment system to your home to filter or condition the water so it is less corrosive to your plumbing system,particularly in areas which have hard water. For more ways to care for and protect your home plumbing system,contact a licensed,professional plumbing contractor in your area to discuss options and products to suit your needs.

Most homeowners underestimate the drain system in their house. Normally,since it’s the type of home zone that’s only noticed when there’s a maintenance issue. To avoid long-term replacements and repair challenges,homeowners should consider professional drain cleaning services. In this article I will inform you of the importance of professional drain cleaning services and what it means for the average Australian home.

Professional Drain Cleaning Services can Eliminate Slow Drains

Often,before the drain becomes clogged it begins to drain slower than before,since it takes longer to drain because of the blockage within the main service line in your home.. Professionals can spot the problem,whether and ensure that any slow drainage issues don’t turn into a large blockage over time. It’s important to call professional leak detectors at this early stage to clean your drains,before long-term damage can occur. Locating the problem as early as possible can help you avoid an unexpected sewer backup that could be messy and expensive to resolve.

Drain Cleaning Professionals can Reduce Home Drain Odours

Oftentimes,even when the drain appears to be functioning perfectly well,unpleasant odour can be noticed in multiple drains. It is possible there is a problem or some kind of serious issue somewhere that a professional plumber has to inspect and solve. Professional leak detectors have both the up to date equipment and the knowledge to respond to any odour-related drain issue. Even more,they can ensure the offending smell is removed within just a few minutes of investigation and service work.

Leak Detectors can Identify Larger Blockages

Drain experts are unreliable when it comes to locating drainage clogs and pipe issues. On the other hand,they might also be able to spot a future,hidden problem within a bathroom or kitchen. It might be a cracked pipe that could cause a serious leak within the system or they might discover an improperly vented gas drain that could be dangerous to those in the property. Their expertise can ensure homeowners are safe and potentially expensive issues are fixed.

By entrusting your home inspection services to the professionals,you can ensure that your system works perfectly in agreement to the highest of standards. We all know that drain blockage and clogs are sometimes dangerous and they must be addressed immediately,especially if there is a gas drain problem. For you as a home owner it is imperial if you notice any suspicious signs to contact your local service provider and to schedule before anything big happen.